Stack SpeedyBee F405 V3 BLS 50A FC&ESC

SpeedyBee F405 flight stack : F405 V3 FC flight controller and 50A 3-6s BLHeli_S 4-in-1 ESC in 30x30mm size . This model can be connected and configured via Bluetooth, has built-in 4-level battery indicators, a 1500 uF filter capacitor, a built-in barometer and much more.

PECULIARITIES

• Dedicated DJI Air Unit connector for quick connection
• 4 x UART for connecting devices: receiver, VTX, camera, GPS
• SD card slot supports up to 4GB of Blackbox data
• BEC: 9V 2A and 5V 2A
• 4-level LED battery indicator
• 8 motor outputs: m1-m8
• Built-in barometer
• Bluetooth control

CHARACTERISTICS

F405 V3 FC flight controller:

• MCU: STM32F405
• IMU(Gyro): BMI270
• USB Port: Type-C
• Barometer: built-in
• OSD Chip: AT7456E chip
• BLE Bluetooth: Supported. Used to configure the flight controller
• Connection method for DJI Air Unit: using a 6-pin connector or soldering
• Support for Blackbox MicroSD memory cards: yes
• BetaFlight camera control panel: yes
• Input current sensor: yes
• Input Power: 3S - 6S Lipo
• ESC outputs: M1 - M4 on the bottom side and M5-M8 on the top
• UART: 6 sets(UART1, UART2, UART3, UART4(for ESC telemetry), UART6)
• ESC: Telemetry UART R5(UART5)
• I2C: supported
• Buzzer: yes
• BOOT button: yes
• RSSI input: yes
• SmartPort: yes
• Firmware support: BetaFlight(Default), EMUFlight, INAV
• Target firmware: SPEEDYBEEF405V3
• Mounting pattern: 30.5x30.5mm (hole diameter 4mm)
• Dimensions: 41.6x39.4x7.8mm
• Weight: 9.6g

*Note: BOOT button. Usage options:
[A]. Press and hold the BOOT button and turn on the FC at the same time to force the FC to enter DFU mode, this is for flashing the FC when the firmware has crashed.
[B]. When the PC is turned on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom side. By default, short press the BOOT button to switch to LED display mode. Long press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.

 SpeedyBee BLS 50A 30x30 4-in-1 ESC Speed ​​Controller

• Firmware: BLHeli_S JH50
• Wireless Configuration: Support SpeedyBee APP
• Link to PC Configurator: https://esc-configurator.com/
• Constant current: 50A x 4
• Peak current: 55A(5sec)
• TVS protection: Yes
• External Capacitor: 1500uF Low ESR Capacitor(Included)
• ESC Protocol: DSHOT300/600
• Input Power: 3-6S LiPo
• Output power: VBAT
• Current sensor: yes
• Mounting size: 30.5x30.5mm (hole diameter 4mm)
• Dimensions: 45.6x44x6.1mm
• Weight: 13.8g

EQUIPMENT

 F405 V3 FC

• 1x SH 1.0mm 30mm 8pin cable (for FC-ESC connection)
• 1x SpeedyBee F405 V3 Flight Controller - 30x30
• 5x M3x8mm silicone bushings (for FC)
• 1x DJI 6pin cable(80mm)

50A 3-6s BLHeli_S 4-in-1 ESC

• 1x SH 1.0mm 30mm 8pin cable(for FC-ESC connection)
• 1x SpeedyBee 50A 3-6S BLHeli_S 4-in-1 ESC - 30x30
• 5x M3x8.1mm silicone bushings (for ESC)
• 1x 35V 1500uF Low ESR Capacitor
• 1x XT60 power cable(70mm)
• 5x M3 silicone O-rings